Processus étape par étape pour monter un kiosque 24" avec le lecteur de carte Wisepad3
Specifications :
K2 24'' Flipdish Kiosque
Video Instructions:
Instructions:
Etape 1 :
Veuillez vous assurer que tous les contenus ci-dessous sont présents.
Plaque de base
La colonne du K2 Kiosque
Le kiosque K2. Cela devrait venir avec des autocollants de marque
La garde de couverture.
Les câbles d'alimentation
3 jeux de boulons. 6 x gros boulons avec rondelles. 6 x boulons moyens. 4 x petits boulons.
2 clés Allen
The base extension.
Etape 2 :
Place the baseplate falt on the floor and sit the base extension on top of it using the largest bolts and washers to secure the 2 pieces together.
Please see the image below.
Step 3.
- Turn the kiosk so the screen is facing the floor.
- Place the spine on top of the kiosks and using the small black bolts.
- Secure the 2 pieces together.
Please see the image below.
Step 4.
Pick the kiosk screen up which has the spine attached to it and slot it into the base extension using the medium-sized silver bolts to secure the 2 pieces together.
Step 5.
Plug the gray wire into the back of the K2 kiosk and run it down to the base of the kiosk. There is a small hole where you can then run the cable out the back of the kiosks.
Please see the image below.
Step 6.
Attach the cover guard to the bottom of the kiosk. The base cover clips in on each side. You may have to apply some pressure so the clips catch.
Step 7.
Before attaching the backplate please first switch the kiosk on.
Please see the image below.
Step 8.
- There are two buttons on either side of the kiosk, please press both of them simultaneously and the front end of the kiosks should fall forward.
- There is another switch that needs to be turned on this can be seen in the bottom left corner of the second image.
Image 1.
Image 2.
Wisepad/Chipper Mounting - K2 Mount Guide
Step 1.
Please ensure all equipment listed below is present.
- K2 Card reader arm Mount
- K2 Card reader holder
- 3 x 4x 10mm Machine screws.
Step 2.
Please remove the black cap on the right-hand side of the kiosk exposing 3 screw holes.
Please see the image below.
Step 3.
Please secure the Card reader Arm to the mount using the 3 bolts provided. Please make sure it is secure.
Please see the image below.
Step 4.
Please attach the Card reader cradle to the Chipper Arm.
Ensure it is attached the same way as in the image below.
Step 5.
Please apply the sticky tape that comes with the card reader to the back of the chipper and push the card reader into the cradle. It should then be hard to remove.
Step 6.
Plug the charging cable into the Chipper.
Please see the image below.
Step 7.
Remove the back of the kiosk. You can do this by pulling down on the 2 clips see in the image below. The clips are at the top of the back of the kiosk.
Step 8.
Once the back of the kiosk is opened you can then plug the other end of the charging cable into the back of the kiosk.
Please see the image below.
Step 9.
Please place the cover of the kiosk back on. The cable will be sticking out as in the photo below.
Please apply pressure to close the back of the kiosk.
K2 Set up
Step 1.
Select the “Start setup button”.
Step 2.
Select the country that the kiosk is located in.
Step 3.
Select the timezone the kiosk is in.
Step 4.
Select a Wi-Fi network and input the password.
Step 5.
Press the skip button on the bottom center of the screen.
Step 6.
Press start configuration on the bottom center of the screen.
Step 7.
Press "Enter the system" on the bottom center of the screen. When a 6 digit code appears on the screen, you can use this to add your kiosk to your WL portal.
To learn more about Flipdish’s products or how to grow your online business enroll for FREE in the Flipdish Academy here: http://academy.flipdish.com/
Commentaires
0 commentaire
Cet article n'accepte pas de commentaires.